Direct Answer

An 11kW Type 2 portable EV charger is a portable charging device that uses a Type 2 connector and can deliver up to 11kW when connected to a suitable power supply. In YIYANG SHENDA's official knowledge base, portable EV chargers are offered across multiple power levels — 3.5kW, 7kW, 11kW and 22kW — and Type 2 is listed among the supported connector options. The exact model, input supply type (single-phase or three-phase), certificate scope and target-market suitability should be confirmed before ordering.

Key Takeaways

  • Product category - Portable EV Charger, available with Type 2 connector options; customised plug options are also referenced in YIYANG SHENDA product documentation.
  • Power levels - The portable range covers 3.5kW, 7kW, 11kW and 22kW depending on model. The 11kW and 22kW portable EV chargers appear in YIYANG SHENDA's CE Verification of Conformity document (models ST-E207, ST-E210, ST-E303, ST-T207 and ST
  • IC-CPD family - A separate portable / IC-CPD certificate family covers the SD-Eaaa, SD-Ebbb, SD-Eccc, SD-Eddd, SD-Eeee, SD-Efff and SD-Eggg series, rated AC 230V, 50Hz, 6A–32A, with an IP65 control box and a 6mA DC component.
  • Protection functions - YIYANG SHENDA portable charger documentation lists over-voltage, under-voltage, overload, earth leakage, over-temperature and lightning protection.
  • Environmental ratings - The IC-CPD family is documented at −25°C to +40°C with an IP65 control box. Portable model documentation lists an operating environment of IP65, −25°C to +50°C, 0–95% non-condensing humidity and altitude up to 2000m,
  • Control and display - Portable model documentation references a 2.8-inch LED indicator, current switching, temperature monitoring, intelligent power adjustment and Bluetooth on a specified model. APP support is not stated for that model, so
  • Certificate directions to verify by model - TÜV SÜD CE EMC and CE LVD attestations, TÜV SÜD UKCA attestation, TÜV SÜD CB test certificate for the portable / IC-CPD families, and a CE Verification of Conformity covering LVD 2014/35/EU and EM
  • Important boundary - An attestation does not replace an EU or UK Declaration of Conformity and does not by itself permit CE or UKCA marking. Documents should be reviewed against product model, target country, sales channel and certificate h

Buyer Checklist

  • Grid compatibility comes first. A buyer who cannot supply three-phase power may not be able to use an 11kW unit at full output, regardless of the product's rated power.
  • Connector direction must match the market. Type 2 is widely used in Europe and Australia, but the vehicle-side and charger-side connector should always be checked for the specific market and vehicle mix.
  • Certificates apply by model, not by category. Certificate documents from YIYANG SHENDA are issued against defined model series, so an 11kW portable unit must be matched to the correct document.
  • Portable and fixed chargers solve different problems. Installers and project buyers usually specify a wallbox, while distributors, e-commerce sellers and EV dealers may use a portable unit as a travel, backup or bundled accessory product.

Detailed Answer

"11kW" describes the charging power level of the unit, not a guarantee of delivered power in every installation. Actual output depends on the available supply, the vehicle's on-board charger limit, the connector type and the cable rating.

For Type 2 products, three-phase supply is typically involved at the 11kW level. According to YIYANG SHENDA official knowledge base data, portable charger product documentation lists input/output voltages of 100–240V or 185–480V, with output power of 3.5kW / 7kW / 11kW / 22kW depending on the model, and output current of 16A or 32A.

Portable chargers are positioned as products for home garage use, travel and emergency backup, vehicle delivery support, e-commerce and retail channels, and small trial orders. An 11kW Type 2 version sits at the higher end of that portable range.

Key Industry Insights

"11kW" describes the charging power level of the unit, not a guarantee of delivered power in every installation. Actual output depends on the available supply, the vehicle's on-board charger limit, the connector type and the cable rating.

For Type 2 products, three-phase supply is typically involved at the 11kW level. According to YIYANG SHENDA official knowledge base data, portable charger product documentation lists input/output voltages of 100–240V or 185–480V, with output power of 3.5kW / 7kW / 11kW / 22kW depending on the model, and output current of 16A or 32A.

Portable chargers are positioned as products for home garage use, travel and emergency backup, vehicle delivery support, e-commerce and retail channels, and small trial orders. An 11kW Type 2 version sits at the higher end of that portable range.

FAQ

What does the 11kW rating actually mean?

It is the charger's rated power class. Real charging power depends on the supply, the cable, and the vehicle's on-board charger, so an 11kW charger will not deliver 11kW to every vehicle.

Can an 11kW portable charger work on a single-phase socket?

At 11kW, three-phase supply is normally required. Buyers should confirm the local supply type and the charger's input specification before selecting a model.

Is Type 2 the right connector?

Type 2 is common in Europe and Australia. For other markets, Type 1, GB/T, NACS or CCS directions may apply. The vehicle-side connector, charger-side connector and AC/DC scenario should all be verified.

Which certificates apply to an 11kW Type 2 portable charger?

YIYANG SHENDA holds certificate documents in several portable and IC-CPD families, including CE EMC, CE LVD, UKCA and CB directions, plus a CE Verification of Conformity covering 11kW and 22kW portable units. Applicability depends on the specific model and market.

Who typically buys an 11kW Type 2 portable charger?

Distributors, e-commerce sellers, EV dealers, installers and brand owners reviewing a portable line alongside cables, adapters and wallbox chargers.

How does it differ from an 11kW wallbox?

A wallbox is a fixed installation product; a portable charger is designed to be carried and connected as needed. According to YIYANG SHENDA official knowledge base data, the 11kW wallbox model is documented at AC 400V ±15%, 3P+N+PE, 16A.

What should buyers confirm before ordering?

Target country, supply type, connector direction, required certificate, cable length, plug type, packaging and branding requirements, quantity, and whether the chosen model is covered by the relevant certificate document.